How to Change a Subaru Spare Key

When you lose your Subaru car key, you should call a locksmith. They can usually cut a new key for you cheaper than the dealer.

Fob remote "push to start" intelligent keys or a basic metal key are the two main types of Subaru car keys. The Fob keys will need to have its chip reprogrammed.

Keyless Entry System

The key fob can be used to lock and unlock your Subaru remotely. It also opens the trunk of your car or the lift gate. The remotes use keys inside your car to connect with your computer system of your vehicle.

Certain models of Subaru have a feature that is not widely known called PIN Code Access. You can use a customized number sequence to start and unlock your vehicle. Check your owner's guide to learn how to get a new subaru key fob to utilize this feature if you have a Subaru Forester, Outback Crosstrek, WRX STI or Impreza.

If your keys stop working, there's an excellent possibility that the battery inside the key fob is dead. The first thing to check is that it's got new batteries and you can do this using a handheld remote tester or a basic multimeter from your garage.

The next step is to take the key fob out of its case and inspect the circuit board that controls the transmitter. There will be one or two sets of 8 numbers. Write down the first so you remember it. After that then put the key fob back together and you'll be ready to program it at home. The procedure for doing this will vary based on the type and year of your vehicle but it's usually easy enough to accomplish yourself.

Key Fobs

Subaru's latest models have key fobs which not only unlock doors, but also activate lights, lock the gas cap, and even start the car. That last trick is especially helpful if you've been at the pump only to find that your car isn't starting because the battery in the key fob was dead.

If your subaru key replacement cost; just click the following post, is new or older, it's likely that the key fob can be replaced with little difficulty. It's important to keep in mind that the most recent models that have high levels of technological sophistication could require an excursion to the dealer. But, with a bit of time and effort, you'll find a replacement key fob to use at home.

Begin by looking at the circuit board for the transmitter inside your key fob (instructions to open the case are provided in the owner's manual). It should have one or two sets of serial numbers each of which is 8 digits long. Keep the first set of numbers in your wallet for later references.

Next, climb into your driver's seat and shut all doors. Turn the key ten times to start your car, and then turn it off. Press the lock button of your key fob, and then open the door. This will verify that your doors are functioning correctly. Then close the door, and remove the key from the ignition. You should hear your car chime again, indicating that the key fob has been programmed.

Ignition System

If your Subaru keys aren't working as they should, it could be because the key battery is dead. You can replace the battery in your key fob at home if you know how. Battery replacement is affordable and easy to find. If your key fob won't respond to your commands, there could be another problem. It's recommended to visit a dealership to purchase a spare key. They can ensure that the key is an original subaru chip key replacement key, which is covered under warranty, and that it will be programmed for your vehicle. This is much simpler and safer than purchasing an aftermarket key from a business online.

You can also have the dealer cut a new key if you supply them with your VIN number as well as evidence of ownership. The information provided will be used to create a code for the key replacement to ensure that it is accepted by your immobilizer. This procedure is more complicated than simply cutting a key, and the dealership will usually charge a higher price for this service.

Once the new key has been programmed then you'll be able switch it to your current key. It will only take you five seconds to insert the new key, so make sure to keep your working key close to hand. You can take the key off after the security light has stopped flashing and you can test it.

Battery Replacement

One of the key features that makes Subaru fobs so beneficial is their ability to turn on your car's power windows and sunroof by pressing of the button. The battery inside your Subaru fob isn't built to last forever, and will need to be changed eventually. Fortunately, replacing the battery is a simple process that you can do yourself with the assistance of this brief guide from Capitol subaru duplicate key.

To begin, you'll need to locate the tiny crevice inside the seam that divides the back and front of your key fob. Using a small flathead screwdriver, you can pop the seam open and reveal a small compartment inside that houses the battery. Remove the old battery, and then put in a new one, ensuring that it is facing the right side up. Once you have assembled everything, you can use the new key fob for locking, unlocking, and starting your vehicle.

Always have a spare set keys, particularly if yours is broken or has gone missing. You can buy a new key from your local dealership or have it cut by locksmiths. In either case, it's vital to get your key fob operating properly as soon as possible to allow you to drive in a safe manner!