How to Change a Subaru Spare Key

When you lose your Subaru car key, you should call a locksmith. Usually, they can cut new keys for you cheaper than the dealer.

subaru smart key car keys are generally either smart "push-to-start" fob remote keys or plain keys made of metal. The Fob key is equipped with an embedded chip and it will require reprogramming.

Keyless Entry System

The key fob can be used to lock and unlock your subaru keys locked in car remotely. It also opens the trunk of your vehicle or the lift gate. These remotes use the keypad of your car to connect to your vehicle's computer.

Subaru models have a little known feature dubbed PIN Code Access. You can choose a personal number sequence to open and start your car. If you have a model newer than Subaru Forester, Outback, Crosstrek, WRX, WRX STI, or Impreza that came with this feature, consult your owner's manual to see how to use it.

It's likely that the battery inside the key fob has died. The first thing you'll need to do is ensure that the key fob has new batteries and you can do this with a portable remote tester or a basic multimeter that you can find in your garage.

Next, you'll want to remove the key fob from its case and inspect its transmitter circuit board. This board will have one or two sets of 8-digit numbers, so jot down the first set so that you are able to recall it later. After you've done this, you can start programming the key fob at home. The procedure for doing this is different based on the model and year of your car, but it's usually simple enough to do by yourself.

Key Fobs

Subaru's most recent models include key fobs that can not only unlock doors, but also switch on lights, lock gas cap, and even start the car. That last trick is especially helpful if you've been at the gas station only to find that your car isn't starting because the battery in the key fob was dead.

No matter if your Subaru is old or new it's likely that the key fob can be replaced without difficulty. It's important to keep in mind that models with a high level of technological sophistication may require an excursion to the dealer. However, with a little time and effort, you can find a replacement key for subaru forester key fob to use at home.

Start by opening the case and inspecting the circuit board of the transmitter. (Instructions on how to open the case are usually included in the owner's manual). It should have two or three serial numbers each one of which is 8 digits long. Write down the number that is the first in the series and keep it in your wallet for reference later.

Then, get into the driver's seat and close all of the doors. Turn the key to start the vehicle, then turn it off after ten turns. Press the lock button of your key fob, and then open the door. This will confirm that your doors are working correctly. Then close the door, and remove the key from the ignition. The chime should be heard from your vehicle again and indicate that the key fob is programmed.

Ignition System

The key battery may be dead If your subaru replacement keys keys aren't functioning as they should. You can replace the battery in your key fob by yourself if know how. A replacement battery is cheap and relatively easy to locate. If the key fob isn't responding to your commands there could be a different issue. It's best to go to a dealer to obtain a spare key. They'll ensure that the key is an original subaru locked keys in car key, under warranty, and that it is programmed to your vehicle. This is much simpler and more secure than purchasing an aftermarket key from a website.

The dealer will also cut a key for you if you provide them with your VIN number as well as evidence of ownership. The information provided will be used to encode the new key so that it can be accepted by your immobilizer. This is a much more complicated procedure than cutting a key, and the dealership will charge you more for it.

Once the new key has been programmed then you'll be able change it over to your existing key. It will take only five seconds to insert the second key, so it's important to keep a working key on hand. When the security light ceases to flash and you're able to remove the new key and check it to ensure it's working correctly.

Battery Replacement

Subaru fobs are extremely useful because they can switch on the power windows and sunroof of your vehicle with just one button press. But, the battery in your Subaru key fob isn't made to last forever and will eventually require to be replaced. This quick guide from Capitol Subaru will help you to change the battery yourself.

First, you'll need to locate the small gap that is the gap between the front and back of your keyfob. With a small flathead screwdriver you can pop this seam open to reveal a small compartment inside that houses the battery. Install the new battery and ensure it is facing correctly. Remove the old one. Once you've assembled everything you can use the new key fob to lock the vehicle, unlocking it, and then starting your vehicle.

You should always have a spare set keys, particularly if the one you have is damaged or has been lost. A new key can easily be purchased at your local dealership for cars or you can have one cut from an locksmith. Whatever you choose, it's essential to get your key fob functioning properly as soon as you can so that you can drive in a safe manner!